3×8 ground protection boards 80 tons load capacity

The LC101 series are ideal for tank weighing, hoppers, suspended loads and truck scales. They have ±0.03% linearity and a 3 mv/V output in capacities from 25 to 40,000 lbf. View Full Specifications. See More Ite from this Family (32) Added to Your Shopping Cart.

port of rigid thermal insulation board. Roof deck is typically installed to endlap approximately 2” over supports. However, it can be butted (or lapped more than 2”) to solve field fit proble. Since design professionals frequently use the installed deck system as

The dimensions of load area 1 are 4’x3.25′ and equals 13 square feet. The dimensions of load area 2 are 6’x3.25′ and equals 19.5 square feet. And since the deck is symmetrical, the load areas 5 and 6 on the opposite side of the deck are identical. This leaves the load areas 3 and 4 in the center area of the deck to be determined.

The maximum spread load should not exceed: for 20' ntainers: 4.8 tons (10,582 lbs) per running meter in length, and 7.6 tons (16,755 lbs) for steel floor ntainers for 40' ntainers: 3 tons per running meter in length, and 6.0 tons (6,614 lbs) for steel-floor ntainers load must not exceed maximum payload

Example 3 Ground Bearing Pressures Tables 1. Crane Weight The maximum weight of the crane to be used 50,000kgs (worst case scenario) 2. Load The maximum load to be lifted 22,000kgs + Load 1,500kgs 3. Outrigger Load Point load = (1+2) x 100% = (50,000 + 23,500) x1 = 73,500kgs or 73.5t 4. Ground Type Ground mes in granular and hesive types.

now Let's find the tributary areas of a deck. To determine the maximum load capacity of your deck, start by calculating its total area and multiply by 50 psf. So, a 100 sqft deck would be designed to support 5000 lbs. Do not get nfused with what weight you might think or want to load the deck with.

Calculating Wire/Cable Size formula for Three Phase Circuits. Wire Circular mils = √3 x 2 x ρ x I x L / (% Allowable Voltage drop of source voltage ) Where; ρ = Specific resistance or resistivity of nductor. D = Distance in Feet (One way) i.e. ½ the total circuit length. I = Load Current.

Specifications: Overall Dimensions: 72.00" x 29" x 29" Folded Dimensions: 36" x 29" x 3.6" Folding Table Weight: 32 lbs / 14.5KG Table Top lor: Off White Table Top Material: HDPE Table Top Thickness: 1.8 inch Frame lor: Gray Frame Material: Powder-Coated Steel Frame Tubing Diameter: 28mm Weight Capacity: 1000 lbs. Package Size: 31.10" x 3

Concentrated load for shear = 0.65(GVW) = 0.65(20,000) = 13,000 lb HS 25-44 Loading For an HS 25-44 truck load, the weight of the tractor truck is 25 tons, or 50,000 pounds. From Figure 6-2, the weight is distributed 20 percent to the front axle and 80 percent each to the rear tractor truck axle and semi­ trailer axle:

250 ft. 14/3 White Solid CerroMax SLiPWire pper NM-B Wire This 600-Volt, grounded, jacketed NM-B cable This 600-Volt, grounded, jacketed NM-B cable wire from Cerrowire is used primarily in residential wiring, including branch circuits for outlets, switches, etc. It can be installed in both exposed and ncealed work in normally dry locations and in air voids of masonry block

Enter the email address you signed up with and we'll email you a reset link.

17,000 lbs (7,700 kg) capacity on deck when load is centered over or between axles. Steps located on front rners. Lifting Rings: Lifting rings at each rner of load deck so sling can be attached for lifting crane. Outriggers: Four hydraulic outriggers of box beam nstruction with direct-connected holding valves.

5 ton (60,000 BTU) 5 5 25 16 14 7 145 97 84 42 12.5 7.5 ton (85,000 BTU) 7.5 7.5 37 24 21 11 219 146 126 63 17 10 ton (120,000 BTU) a 5 (x2) 10 49 33 28 14 145 97 84 42 12.5 10 ton (120,000 BTU) 10 10 49 33 28 14 250 167 144 72 20 15 ton (180,000 BTU) a 7.5 (x2) 15 74 49 42 21 219 146 126 63 17 15 ton (180,000 BTU) 15 15 74 49 42 21 375 250 217

3. A load duration factor (CD) of 1.0 is used in determining design loads in this Tech Note. This is nserva-tive for load durations less than normal load duration. 4. Tables 1 and 3 ntain the axial mpression design loads for incised lumber. Lumber design values are adjusted by the incising factor Ci. Design Properties Ci MOE (E) 0.95 Fc